Configuration of a Libre Hosting aka Anouncing our public IPs to Internet from an indifferent places¶

technical resume: IPSec between OPNSense and OpenBSD to announce our ASN IP from an indifferent ISP place.

General presentation¶

Who we are¶

Aquilenet is a non profit organization since 2010 and a "do it yourself ISP", member of a Federation of similar ISP in France called FFDN. We are netneutrality builders, helping for more freedom and building networks using and participating Libre Software.
We provide xDSL, VPN and we hope soon Fiber accesses, and a lot of services for our members (mail, nextcloud, hosting, VPS...) and for others searx, Etherpad, Pastebin, Peertube, ...

The need: create a Libre format hosting in our cool local called "la mezzanine".¶

To allow our the members of our non-profit organization to connect the hardware they want (like Nuc, Raspberry pi, tower, etc...) in our Libre hosting space called "la mezzanine" with a Public IPv6 and IPv4 and from our ASN, we need to announce our IPs from another place than our Datacenter.

How we do¶

We have to tunnel all the network from the Libre Hosting to Internet and vice versa. We have tried first with OpenVPN but the userland application use to much resources for needed bandwidth (200Mbps).
This IP range will be routed by IPSec to our ASN point of BGP announce in our datacenter, then they will route them to the Libre Hosting.

From our Libre Hosting we have a OPNSense Firewall and in our Datacenter two clustered OpenBSD.

A scheme to explain this:

Scheme explanation:

• (1) ASN & BGP

With our ASN with can do BGP to announce our IP adresses in our Datacenter.

• (2) Firewalls in the Datacenter

The job is done with a cluster of firewalls using the magic power of OpenBSD and OpenBGPD.
For firewall Redundancy we use CARP and pfsync

• (3) La Mezzanine

Is our cool place where we can meet our members and friends.
This place use green power with an alternate electricity supplier, called Enercoop is a French electric utility cooperative company, which only uses renewable energy.
Here, the firewall is OPNSense doing the PPPOE connection on a general public fiber provider (Yes we had to hack a little to remove this ISP baclkbox).

• (4) Public IPv6 and v4 from the Mezzanine to Internet

This firewall is routing threw an IPSec tunnel (for each OpenBSD firewall) our public dedicated IP for this place. These IP allow our friend's to put there their servers servers / Arduino's & co to Internet with our network <3

---

Technical information¶

OpenBSD configuration¶

We configure the OpenBSD's IPSec configuration file for 2 Phase 2 tunnels one for IPv4 another on for IPv6

/etc/ipsec.conf

ike passive esp from any to $LIBRE_HOSTING_PUB_IP_V4/26 \
    peer $OPSense_Public_IP\
    main group modp2048\
    psk "mysupersecurepass"

flow esp from any to $LIBRE_HOSTING_PUB_IP_V4/26 peer $OPSense_Public_IP
flow esp from any to $LIBRE_HOSTING_PUB_IP_V6/48 peer $OPSense_Public_IP

chmod 500 /etc/ipsec.conf

Launch the tunnel:

isakmpd -K  
ipsecctl -f /etc/ipsec.conf

To make it permanent add this to /etc/rc.conf.local:

isakmpd_flags="-K"
ipsec_rules=/etc/ipsec.conf
ipsec=YES

check the configuration:

ipsecctl -sa 

Enable some logs on Isakmpd:

sh -c "echo S \> /var/run/isakmpd.fifo"  
less /var/run/isakmpd.result

and:

isakmpd -d -DA=70 -K

Check IPSec Flows:

ipsecctl -F

OPNSense configuration¶

\-> Configuration1: Performances¶

• AES_CBC_256/HMAC_SHA2_512_256/MODP_8192

• Cerbere11

last pid: 45038; load averages: 0.27, 0.34, 0.31 up 0+00:56:47 19:07:15

49 processes: 1 running, 48 sleeping

CPU 0: 3.9% user, 0.0% nice, 0.8% system, 3.1% interrupt, 92.1% idle

CPU 1: 1.2% user, 0.0% nice, 0.0% system, 6.3% interrupt, 92.5% idle

CPU 2: 0.4% user, 0.0% nice, 0.0% system, 21.3% interrupt, 78.3% idle

CPU 3: 5.9% user, 0.0% nice, 0.0% system, 2.4% interrupt, 91.7% idle

Mem: 109M Active, 145M Inact, 387M Wired, 152M Buf, 7214M Free

• Cerbere1

load averages: 1.18, 0.95, 0.74 cerbere1.aquilenet.fr 19:08:23

43 processes: 1 starting, 40 idle, 1 dead, 1 on processor up 3 days, 18:40 up 3 days, 19:21

CPU0 states: 0.2% user, 0.0% nice, 2.8% system, 7.4% interrupt, 89.6% idle

CPU1 states: 0.0% user, 0.0% nice, 22.4% system, 0.0% interrupt, 77.6% idle

CPU2 states: 0.0% user, 0.0% nice, 20.2% system, 0.0% interrupt, 79.8% idle

CPU3 states: 0.0% user, 0.0% nice, 10.8% system, 0.0% interrupt, 89.2% idle

Memory: Real: 584M/2111M act/tot Free: 5793M Cache: 754M Swap: 0K/8405M

• bande passante

MTU¶

Linux: ping -M do -s 1172 185.233.102.130 => OK

Linux: iperf3 -c 185.233.102.130 -M 1160 => OK

Linux: ping -M do -s 1173 185.233.102.130 => NOK

Linux: iperf3 -c 185.233.102.130 -M 1161 => NOK

• netcat qui fait un echo
  socat TCP4-LISTEN:4444,fork EXEC:cat